Visible light activated TiO2/microcrystalline cellulose nanocatalyst to destroy organic contaminants in water

Hybrid TiO2/microcrystalline cellulose (MC) nanophotocatalyst was prepared in situ by a facile and simple synthesis utilizing benign precursors such as MC and TiCl4. The as-prepared nanocomposite was characterized by XRD, XPS, BET surface area analyzer, UV–vis DRS and TGA. Surface morphology was assessed by the means of SEM and HR-TEM. Statistics-based factorial design (FD) was adopted to investigate the effect of precursors concentrations and therefore to optimize the nanocomposite synthesis through catalytic adsorption of methylene blue (MB) from aqueous solutions. The results indicated that TiO₂/MC nanocomposites were photocatalytically active in diminishing 40–90% of MB in 4 h.

Ag/AgCl composite nanoparticles/polyacrylonitrile nanofiber films for visible-light photocatalysis

Ag/AgCl composite nanoparticles/polyacrylonitrile nanofiber films were prepared by electrospinning and subsequent in-situ reduction combining in-situ oxidation strategy. Electrospinning was firstly used to fabricate PAN/AgNO3 composite nanofibers; then the AgNO3 was reduced by in-situ reduction with glycol; finally, an in-situ oxidation between Ag nanoparticles and FeCl3 solution was carried on to prepare the compo-site nanofiber films. The as-prepared materials can be used as high-performance photocatalysts, taking the advantage of the visible-light activity, flexibility, and high photocatalytic kinetics. The present method is helpful for the development of the high-performance membrane based photocatalysts.

Fabrication and visible-light photocatalytic behavior of perovskite praseodymium ferrite porous nanotubes

Perovskite praseodymium ferrite (PrFeO3) porous nanotubes are prepared by electrospinning of the precursor solution into nanofibers, subsequently by annealing the precursor fibers at a low temperature (e.g. 40 °C) and finally by calcination at a high temperature. The low temperature annealing treatment is found to play a key role in the formation of porous nanotube. The porous tubes show a perovskite-type PrFeO3 crystal characteristic with high optical absorption in the UV-visible region and an energy band gap of 1.97 eV. When compared with PrFeO3 porous nanofibers and PrFeO3 particles, the PrFeO3 porous nanotubes show better visible-light photo-catalytic ability to degrade Rhodamine B in aqueous phase because of the increased surface area and more active catalytic sites on the inner walls and outer surfaces.

Self-cleaning wool: effect of noble metals and silica on visible-light-induced functionalities of nano TiO2 colloid

© 2014 The Textile Institute. This study intends to enhance the functionality of titanium dioxide (TiO2) nanoparticles applied to wool fabrics under visible light. Herein, TiO2, TiO2/SiO2, TiO2/Metal, and TiO2/Metal/SiO2 nanocomposite sols were synthesized and applied to wool fabrics through a low-temperature sol–gel method. The impacts of three types of noble metals, namely gold (Au), platinum (Pt), and silver (Ag), on the photoefficiency of TiO2 and TiO2/SiO2 under visible light were studied. Different molar ratios of Metal toTiO2 (0.01, 0.1, 0.5, and 1%) were employed in synthesizing the sols. Photocatalytic efficiency of fabrics was analyzed through monitoring the removal of red wine stain and degradation of methylene blue under simulated sunlight and visible light, respectively. Also, the antimicrobial activity against Escherichia coli (E. coli) bacterium and the mechanical properties of fabrics were investigated. Through applying binary and ternary nanocomposite sols to fabrics, an enhanced visible-light-induced self-cleaning property was imparted to wool fabrics. It was concluded that the presence of silica and optimized amount of noble metals had a synergistic impact on boosting the photocatalytic and antimicrobial activities of coated samples. The fabrics were further characterized using attenuated total reflectance, energy-dispersive X-ray spectrometry, and scanning electron microscopy images.

Visible transparent, UV-blocking polymer nanocomposite films containing nano-sized organic-LDH (Layered Double Hydroxide) hybrid

A nano-sized Mg2Al layered double hydroxide (LDH) was used for encapsulating an organic UV absorber, 2-hydroxy-4- methoxybenzeophenone-5-sulfonic acid (HMBS), to produce HMBS@LDH hybrid nano-platelets. Upon dispersing this organic-inorganic hybrid LDH into ethylene-vinyl alcohol copolymer (EVOH) for film casting, a thin polymer
nanocomposite film that is UV opaque but highly transparent to visible light (higher than 90%) was formed. Thermogravimetry (TG) analysis confirmed that the intercalation of HMBS into LDH considerably increased the thermal stability of HMBS. Such an improvement was attributed to the strong guest-host interaction between the HMBS anions and the LDH layers. Also, the nanocomposite films were flexible and had good mechanical properties.

Visible and UV functionality of TiO2 ternary nanocomposites on cotton

This research intends to increase the photocatalytic efficiency of cotton fabrics coated with TiO2-based nanocomposites under illumination particularly visible light. The fabrics were functionalized using a low-temperature sol-gel method of TiO2/Metal/SiO2 nanocomposite systems. Integrating silica and noble metals into TiO2 sol was put forth for boosting its functionality. Three noble metals (gold (Au), platinum (Pt) and silver (Ag)) with four different concentrations were employed. The photocatalytic activity of the functionalized fabrics was assessed through coffee stain-removal test and photodecomposition of methylene blue (MB) under UV and visible light. The impact of coating layers on fabrics' hydrophilicity was analyzed through measuring the water contact angle as well as the water absorption time. The fabrics were characterized using XRD, SEM and EDS. It was corroborated that the presence of silica enhanced the self-stain-removal capability of fabrics under UV. Moreover, the self-cleaning property of fabrics improved under both UV and visible light after integrating the metals into the colloids. In the same line, the self-cleaning activity threshold of fabrics was shifted to visible region.

Isorefractive high internal phase emulsion organogels for light induced reactions

Isorefractive high internal phase emulsion (HIPE) organogels have been fabricated and investigated for light induced reactions. High transparency facilitates both the UV and visible light induced reactions within HIPE organogels. Transparent HIPE organogels are advantageous for light induced polymerizations, accelerating such polymerizations and enabling the preparation of large polyHIPE monoliths.

Facilitated heterogeneous photodegradation of dissolved organic matter by particulate iron

The photochemical degradation of dissolved organic matter (DOM) derived from the leaves of River Red Gum (Eucalyptus camaldulensis) was examined, with a particular focus on the photochemical generation of CO₂, consumption of O₂, and the effect of particulate iron minerals on these photochemical reactions. Solutions of leaf leachate were irradiated with ultraviolet and visible light in the presence and absence of amorphous iron oxides. Addition of fresh iron oxide was found to increase the rate of photodegradation of the organic matter by up to an order of magnitude compared to the reactions without added iron oxide. The ratio of CO₂ produced to O₂ consumed was ~1:1 in both the presence and absence of iron oxyhydroxide. The reactivity of the iron oxides was dependent on the preparation method and decreased with increased storage time. These results suggest that photochemical reactions on particle surfaces should be considered when examining carbon transformation in aquatic ecosystems, especially at sites with potential for the production of iron oxyhydroxides.

Luminescence and microstructure of Sr2Mg(BO3)2 doped with Eu

Sr₂Mg(B0₃)₂ doped with Eu was synthesized respectively in air and weak reducing atmosphere (combustion of carbon particle), whose photoluminescence characteristics and structure were also studied at room-temperature. In air, the fluorescent body's color was white for different synthesized temperatures. At room temperature, the sample was excited and showed red typical emission spectrum of Eu³⁺ whose emission apex were sharp near 612 nm and emission spect~m was made up of the charge transformation band (CTB) of Eu^{3 +} and excitation spectrum of 4f→4f high energy level transition, then reached the area of VUV. However, under reducing atmosphere (combustion of carbon particles), the color of the sample yielded was yellow, whose color became deeper with increasing temperature and showed phase transition. Using UV excitation, the luminescence of yellow sample was very weak. In a complicated broad spectrum at visible light area, the red emission spectrum of Eu²⁺ was not observed. Crystal structure and luminescence of the sample were completely different from the results of Diaz and Keszler. Two samples were prepared under oxidation and reducing atmosphere at high temperature, which were different on crystal structure and microstructure. By studying Sr₂Mg(B0₃)₂:Eu³⁺ a series of directional faults or educts were found, because Eu^{3 +} ions substituted for Sr^{2 +} ions. However, microstructure of Sr₂Mg(B0₃ )₂: Eu^{2 +} is more complicated, whose excitation spectrum might be excited by Eu^{2 +}. By XRD patten of the samples, phase transitibn could be found. Twins and clusters that were formed from point defect such as interstitial atom and big angle crystal boundary could be found by TEM.

Abnormally high optical transmittance of refractive-index modified ZnO / organic hybrid films

Hybrid films consisting of ZnO nanoparticles and organic matrices were fabricated at particle concentration levels of up to 60 wt%. The correlation between the refractive index and optical transmittance in the visible light region was investigated. The refractive index of the hybrid films was modified in a continuous manner in the range from 1.44 to 1.55. The refractive index increased linearly as a function of particle concentration. On the other hand, optical transmittance showed little change above the particle volume fraction of 0.08.

The effect of dyes on photo-induced chemiluminescence emission from polymers

Weak photo-induced chemiluminescence (PICL) emission is observed when polymers are exposed to UVA or visible light. The presence of dyes can either increase PICL intensity via Type I photosensitisation which generates polymer free radicals, or reduce it via photo-protection. PICL studies on the eight Blue Wool Standards (BWSs) that are used commercially as lightfastness standards show higher PICL intensity from the least photostable BWSs that use triphenylmethane dyes and lower intensity from more photostable BWSs using UVA and visible wavelengths. The relative PICL intensities do not correlate in a stepwise manner with lightfastness ratings of the BWSs. However dye/polymer combinations that emit high levels of PICL relative to the undyed material are unlikely to have acceptable lightfastness. The xanthene dyes fluorescein and eosin Y are more strongly photosensitising than triphenylmethane dyes on wool and both produce higher PICL emission than undyed wool when irradiated with visible light.

UV-shielding ceramic nanoparticles synthesised by mechanochemcial processing

ZnO, TiO₂ and CeO₂ are known as UV-shielding ceramic materials that have advantages over organic UV absorbers for their photo-stability and non-hazardous nature to human bodies. However, they normally cause low transparency in the visible-light range due to light scattering by large particles, which is undesirable for many transparent UV-blocking applications in cosmetic and plastic industries. Light-scattering efficiency of particles can be drastically reduced by decreasing the particle sizes down below 100 nm. This paper reviews recent investigation on the synthesis of ZnO and CeO₂ nanoparticles by mechanochemical processing. The resulting particles had a significantly low degree of agglomeration, having mean particle sizes of ~ 25 nm and ~ 10 nm, respectively. The aqueous suspensions of the nanoparticles showed strong absorption in the UV-light range and high transmittance in the visible-light range. Mechanochemical processing offers the possibility of industrial-scale production of transparent UV-shielding ceramic particles for many applications.

Polymer coatings containing nano particles of zinc oxide for the UV protection of dyed polyester fabrics

The useful life of many outdoor textile products is limited by degradation caused by exposure to sunlight, in particular by the ultra violet component (below 400 nm). The degradation results in fading of colours and also loss of physical properties, such as tear strength and abrasion resistance. Degradation can be decreased with UV absorbers, often used in conjunction with antioxidants or free radical quenchers. The protection afforded by these organic compounds is, however, limited as they are ultimately destroyed by the UV radiation they absorb.
An alternative approach is to coat fabrics with a polymer containing an inorganic UV absorber, such as zinc oxide. The inherent stability of zinc oxide would be expected to provide a protective effect over a much longer period than can be achieved with an organic UV absorber. A possible disadvantage of zinc oxide when applied in a polymer film is that absorption and scattering of visible light can produce hazy films and, hence, an unacceptable change in fabric appearance.
This poster paper examines the possibility of using nano particles of zinc oxide dispersed in acrylic polymers for protecting dyed polyester fabrics against sunlight fading. Factors affecting both UV absorbance and film clarity will be discussed. The possibility will also be examined that the protective effect may be reduced in some circumstances by reactive oxygen species, generated by the interaction of UV with zinc oxide in the presence of air and water.

Partial exfoliation of layered double hydroxides in DMSO : a route to transparent polymer nanocomposites

Layered double hydroxides (LDHs), either having nitrate counter anions or intercalated with organic molecules, have been for the first time partially exfoliated in dimethyl sulfoxide (DMSO) to form a transparent suspension. Atomic force microscopy (AFM) images showed that both the lateral size and the thickness of the LDH nanoplatelets were decreased after the exfoliation. The organic-LDHs maintained their intercalation characteristics, i.e. the thermal stability improvement of the incorporated organic anions, after the exfoliation in DMSO. Transparent ethylene-vinyl alcohol copolymer (EVOH) nanocomposite films containing partially exfoliated LDHs intercalated with UV absorbers were prepared using DMSO as the processing solvent. As the first reported example of a highly transparent LDH/polymer composite, the obtained composite film had a visible light transmittance of 90% (comparable to that of the pure matrix), was flexible and exhibited an excellent UV-shielding capability and thermal stability.